IR100-Series Multifunction IR Remote Control Timer
●Operation & Keys function of IR Controller
1 [ALL ON] Press [ALL ON] key, all ID 1~8 ON
2 [ALL OF] Press [ALL OFF] key, all ID 1~8 OFF
3 [1ONOFF]~[8ONOFF] ON or OFF the corresponding ID No.
4 [T1] Timing to OFF the corresponding ID No.
5 [-T1] Timing to ON the corresponding ID No.
6 [T1T2] Timing ON OFF auto cycle corresponding ID No. T1 ON T2
OFF
7 [B] Press [B] key to disable or enable the buzzer on IR Receiver
(For IR1xxR1- only)
●T1T2 Digital time setting (Note 1: Keying over 10S is invalid.)
* Time of ID 1~8 = (time interval 1~99) x (time unit of 1S 10S 1M or
10M) Time range= 1S~990M,
* [T1] time interval:
1 Press [PROG] key
2 Press [0~9] key for tenth
3 Then press [0~9] key again for unit.
4 Final press [T1] key to enter & to operate T1.
* [T2] time interval:
1 Press [PROG] key
2 Press [0~9] key for tenth
3 Then press [0~9] key again for unit.
4 Final press [T1T2] key to enter & to operate T1T2. (Key of [T1T2]
represents T2 while setting time.)
* [T1][T2] time unit
1 Press [PROG] key
2 Final press [1S] key or [10S] or [1M] or [10M] to enter & to operate
new time unit. (T1T2 use same time unit)
●Power ON Mode Selection-DIP SW No. 4 or Slide SW on housing (Power
OFF before selection)
SW ON ....Power ON to operate T1 mode
SW OFF...Power ON to operate continuous mode
●ID No selection: DIP SW of 1 2 3 ON or OFF to form 8 different Nos for
IR1xxR1- (DIP SW ●=ON ○=OFF)
DIP SW
|
ID 1
|
ID 2
|
ID 3
|
ID 4
|
ID 5
|
ID 6
|
ID 7
|
ID 8
|
No. 1
|
○
|
●
|
○
|
●
|
○
|
●
|
○
|
●
|
No. 2
|
○
|
○
|
●
|
●
|
○
|
○
|
●
|
●
|
No, 3
|
○
|
○
|
○
|
○
|
●
|
●
|
●
|
●
|
If DIP SW 1 2 3 All ON The ID No. is 8(ID 8)
If DIP SW 1 2 3 All OFF. The ID No. is 1(ID 1)
Refer left table. The combination for other Nos
|
●Electric Specifications of IR Receiver (equipped with IR Control Timer)
1 IR100R1-EHU: E27 lamp holder. 300W 100~240VAC 50/60Hz. standby 0.3W & relay on 3W, fuse 5A
2 IR101R1-L7U: E27 LED bulb 7W 6000K 595lm life time 50,000Hrs for 100~240VAC 50/60Hz. On 10W standby 0.3W fuse 1A
3 IR102R1-L3D: MR16 GX5.3 base LED bulb 3W 6000K 255lm life time
50,000Hrs, 12VAC/DC. On 6W standby 0.3W
4 IR102R1-L3U: E27 LED bulb 3W 6000K 255lm life time 50,000Hrs,
100~240VAC 50/60Hz. On 6W standby 0.3W fuse 1A.
5 IR103R1-WWU: 1 output 5A100~240VAC 50/60Hz .Source is Black-White, output is Brown-Black . Relay on 3W. Standby 0.3W
6 IR103R3-WWU: 3 outputs each 3A 100~240VAC total 5A. Source is Black-White. Output wire of Brown is ID 1, Red is ID 2, Orange is ID 3 & Black is common. For multiple loads, standby 0.3W & relays on 3W, fuse 5A.
7 IR104R1-WHU: E27 Holder/w plate IR104P. 300W 100~240VAC.
Source is black-white. Standby 0.3W, relay on 3W, fuse 5A.
8 IR104R3-WWU: 3 outputs/w plate IR104P each 3A 100~240VAC total 5A. Source is Black-White & output wire of Brown is ID 1, Red is ID 2, Orange is ID 3 & Black is common. For multiple lamps. Standby 0.3W & relays on 3W, fuse 5A.
9 IR103R1-CRU: Receptacle 3A 100~240VAC50/60Hz wit AC cord 6 ft.
Standby 0.3W & relays on 3W, fuse 5A.
●Battery: IR100T1-AAA(1.5V)x2; IR100T2-CR2025x1
●Time & accuracy :1~99S 10~990S 1~99M 10~990M +-0.1%
● Dimensions: mm
IR100R1-, D70*H80
IR101R1-L_U D88*H112
IR102R1-L3U D50*L82
IR103R1-, IR103R3- L100*W46*H25
IR104R1-, IR104R3- D113*H58
●Ambient conditions 40oC 85%RH Max
●LED indicator & buzzer on IR Receiver/Timer
1 Press key:LED flashes once & buzzer sounds when IR Receiver/Timer
received signal from IR Controller properly
2 LED flashes: Shows IR Receiver/Timer powered and timing now.
Flash rate is 1S 2S 3S 4S to represent the
time unit of 1S 10S 1M &10M respectively. Flash rate of 5S shows
receiver output is continuous
3 LED steady ON : IR Receiver/Timer is OFF and under standby.
4 3 output LED: LEDs on shows output of ID 1, 2, 3 of IR103R3-
IR104R3- |